Checked the smart info and no reported problems. Change the password. The only way I can think of is the serial port. The HSZ IP-Address for the Zyxel Router is 192.168.1.1, all hosts in the HSZ are using this IP-Address as As I say the same code is fine on a NAS325v2. I believe that programmers should check whether by entering a password with a symbol and specifically the $ is not correctly interpreted by the firewall. 255.255.255.240, Setup Default Gateway to Thought about the serial interface but I'd have to set up a console. 255.255.255.0 is used). This worked fine on my NAS325v2 using the "poweroff" command. as in the Standard Mode. (a Router/Firewall or your PC) to use that can be configured for PPPoE authentication. from the Internet Service Provider. I *think* this means it's not a hanging umount. Router(psm)#atsh. I put the same shutdown code as mine on the same model usb stick and YUP it failed to close down cleanly! We Same USB stick model but different hard drives. To create an administrative account, use the following command format: 'username password user-type admin'. The Zyxel configuration is again very simple, November 2018 edited December 2018 in Questions. The box was left with all LEDs lit but no way (telnet, http, etc) to access it. Intriguingly, I note from the WEB Interface scripts that there is reference to a shutdown command "/ck6fup6/system.main/shutdown" that is part of the zysh command set. Easiest solution (FW is malfunctioning and version 4.30 AAPH0 installed, 4.31 solves this bug!). 83.251.44.193 from the Provider. I've found the halt command, halt_wrapper script (calls halt) and the /etc/init.d rc.shutdown script (but does this do a shutdown or just the fore work). The result was that after the 15 mins inactivity being checked for the script executed "halt &" "exit 0" and left itself idle with all LEDs steady. It only took a couple of hours to knock up and it could be a fun tool. The usb_key_func.sh script simply calls a second script that writes the pseudo daemon script to /tmp. On reboot it started a resync!!! 255.255.255.0 is used). And I would be able to remove my WOL daemon from all boxes and my watch&start code on the router (for the TV's - no WOL on a TV!). addresses and usually also the TCP/UDP port numbers of IP packets as they pass If your raid array gets damaged by that action, then I think the power is cut before the disks have flushed their caches. So it would need to be hosted either as a package install or on a small share on the main drives. which can handle the PPPoE authentication. We Saves me a trip to the affected customers and the downtime. Log into the device via PuTTY or Tera Term. In the SMT main menu, type 24 to enter the system Maintenance screen. (On the 325 that boils down to the same action, power off the box. Further I added a "sleep 60" to rc.shutdown. as in the Standard Mode. Most systems using NAT do so in order to enable multiple hosts on a The Zyxel Most systems using NAT do so in order to enable multiple hosts on a Other than that shutting down seemed a piece of cake until I bought the NAS326! No usb inserted and it's not there! I see no open files left on the stick. Please go to this page to get your Support. Odd. Open files can be caused by processed which for some reason resist to be killed. Well I'm stumped. If you remove a stick the node is freed, and when you plug it in again the node is reused. I also noted, looking through the Zyxel scripts, that they call halt - so maybe I'll try that as well. If you want to get involved, click one of these buttons! 2. Ah well in that case you wouldn't like to write a Sleep.On.Idle.Daemon per chance :-). Copyright © 2020 Zyxel and/or its affiliates. does not exist in the current formal released firmware version (4.33), we had
Just ran into this issue. In this article, I will explain all three modes, the Transparent www.zyxel.com Step 4: Enter the CLI command “configure terminal” to enter configuration mode.